AutomotiveCloudWatch

Glossary · Automotive

Chassis and Dynamics

117 terms in the Automotive glossary, each with its one-line definition.

117 terms, A to Z

  • Ackermann Steering Geometry Steering linkage layout that turns the inner front wheel more sharply than the outer one so both roll cleanly around the same turn center.
  • Active Anti-Roll Bar: A split anti-roll bar joined by a motor or hydraulic actuator that can stiffen to keep the body flat or decouple for comfort and off-road travel.
    Active Anti-Roll Bar A split anti-roll bar joined by a motor or hydraulic actuator that can stiffen to keep the body flat or decouple for comfort and off-road travel.
  • Active Suspension Suspension that uses powered actuators to push and pull the body, holding it level and smoothing the road beyond what springs and dampers can do.
  • Adaptive Damping Shock absorbers whose firmness is changed electronically while driving, letting one car switch between soft comfort and firm control.
  • Air Suspension Suspension that uses compressed air bags instead of steel springs so the vehicle can raise, lower and level itself under any load.
  • Anti-Dive and Anti-Squat Suspension geometry features that limit nose dip under braking and rear sag under acceleration by angling the links.
  • Anti-lock Braking System ABS A system that stops wheels locking under hard braking by rapidly pulsing brake pressure, so the driver can still steer.
  • Anti-Roll Bar A spring steel bar linking the left and right wheels that twists in corners to resist body lean.
  • Body Roll The sideways lean of a car's body toward the outside of a corner.
  • Brake Assist BA A system that detects a panic stop and applies full braking force even if the driver does not press the pedal hard enough.
  • Brake Blending Coordination of regenerative motor braking and friction brakes in an electrified vehicle so the pedal feels smooth and consistent.
  • Brake Booster The device that multiplies the driver's pedal force, using engine vacuum or, in EVs, an electric motor.
  • Brake Caliper The clamp on a disc brake that squeezes the pads onto the spinning disc using hydraulic pistons.
  • Brake Fade A loss of braking power when brakes overheat during long descents or repeated hard stops.
  • Brake Judder A vibration felt through the steering wheel and pedal when braking, usually caused by uneven brake disc thickness.
  • Brake Proportioning The split of braking force between front and rear wheels so the rear wheels never lock before the front.
  • Brake-by-Wire Braking in which the pedal sends an electronic signal to a controller instead of pushing fluid directly to the wheels.
  • Bump Steer Unwanted steering of a wheel by itself as the suspension moves up and down over bumps.
  • Bump Stop The rubber or foam cushion that limits suspension compression and progressively stiffens it near full travel.
  • Bushing A flexible rubber sleeve at suspension joints that allows small movements and absorbs vibration.
  • Camber The inward or outward tilt of a wheel seen from the front, with negative camber helping cornering grip.
  • Caster The backward or forward tilt of the steering axis seen from the side, which makes the steering want to return to straight ahead.
  • Center of Gravity CG The single point where a vehicle's weight can be treated as concentrated, whose height drives rollover risk and handling.
  • Chassis A car's running gear, meaning the suspension, steering, brakes, wheels and tires and the subframes they mount on.
  • Coil Spring A spiral steel spring that holds up the car's weight and compresses over bumps.
  • Conicity and Ply Steer Small sideways forces a tire makes even when rolling straight, caused by tiny build asymmetries, which can make a car pull.
  • Contact Patch The small area of each tire that touches the road at any moment, roughly the size of a hand on a passenger car.
  • Control Arm A hinged suspension link connecting a wheel to the body or subframe while letting it move up and down.
  • Corner Module A self-contained unit packaging steering, braking, suspension and sometimes a drive motor for a single wheel.
  • Cornering Stiffness How much sideways force a tire builds for each degree of slip angle, a core input to handling balance.
  • Damper The suspension part, usually called a shock absorber, that stops the body bouncing after a bump.
  • Differential A set of gears that drives the two wheels on an axle while letting them turn at different speeds in corners.
  • Disc Brake A brake that slows the wheel by squeezing friction pads against a spinning metal disc attached to the hub.
  • Double Wishbone Suspension Suspension that locates each wheel with two A-shaped arms, one above the other, for precise camber control.
  • Drum Brake A brake that slows the wheel by pushing curved shoes outward against the inside of a spinning drum.
  • Effective Rolling Radius The distance a tire travels in one revolution divided by two pi, which is smaller than its unloaded radius.
  • Electric Power Steering EPS Steering assisted by an electric motor instead of an engine-driven hydraulic pump.
  • Electro-Hydraulic Brake EHB A brake-by-wire system in which an electric pump creates brake pressure on demand while keeping conventional wheel calipers.
  • Electromechanical Brake EMB A dry brake-by-wire system in which an electric motor at each wheel presses the pads directly with no brake fluid.
  • Electronic Brakeforce Distribution EBD An ABS-based function that automatically shares braking effort between front and rear and left and right wheels according to load.
  • Electronic Parking Brake EPB A parking brake applied by a switch, usually through motors in the rear calipers, instead of a lever or pedal.
  • Electronic Stability Control ESC A safety system that brakes individual wheels and cuts power to stop a car skidding or spinning.
  • Fishhook Test A US rollover test in which a robot steers sharply one way then hard the other to see if a tall vehicle lifts its wheels.
  • Four-Poster Rig A lab test machine with a hydraulic actuator under each wheel that shakes a complete car to reproduce roads indoors.
  • Friction Circle A picture of a tire's fixed total grip, which must be shared between braking or accelerating and turning.
  • Hill Descent Control HDC An off-road feature that automatically holds the vehicle at a slow steady speed down steep or slippery slopes.
  • Hill Start Assist HSA A feature that briefly holds the brakes on a slope so the car does not roll back while the driver moves to the accelerator.
  • Hydraulic Power Steering HPS Steering assisted by fluid pressure from a pump, usually engine driven, now largely replaced by electric systems.
  • In-Wheel Motor An electric motor built into a wheel that drives it directly without shafts or gears from a central motor.
  • Independent Suspension Suspension that lets each wheel on an axle move up and down on its own without directly affecting the other side.
  • Integrated Brake System IBS A single compact unit combining the brake booster, master cylinder and stability control pump.
  • Jounce and Rebound The upward movement of a wheel toward the body over a bump and its downward movement away from the body.
  • Kinematics and Compliance K&C Rig measurement of how wheel position changes as the suspension moves and as forces act on the tires.
  • Lateral Acceleration The sideways acceleration a car and its occupants feel while cornering, usually expressed in g.
  • Lateral Load Transfer The shift of load from the inside tires to the outside tires when a car corners.
  • Leaf Spring A suspension spring of stacked curved steel strips, usually mounted lengthwise under a solid rear axle.
  • Limited-Slip Differential LSD A differential that stops one wheel spinning uselessly when it loses grip, sending more drive to the wheel that can use it.
  • Longitudinal Slip The percentage difference between a tire's tread speed and the vehicle's speed during braking or acceleration.
  • MacPherson Strut The most common front suspension, in which a combined spring and damper unit also serves as the steering pivot.
  • Magnetorheological Damper A shock absorber filled with iron-particle fluid that thickens instantly in a magnetic field to change firmness.
  • Moose Test An emergency swerve maneuver that steers sharply out of the lane and back at speed to test stability.
  • Motion Ratio How far a spring or damper compresses for each unit the wheel moves, which converts spring rate to wheel rate.
  • Multilink Suspension Suspension that locates each wheel with three to five separate links so each motion can be tuned independently.
  • Oversteer When the rear tires lose grip before the front ones and the car turns more sharply than intended.
  • Pitch The forward and backward rocking of a car body, seen as nose dive under braking and rear squat under acceleration.
  • Pneumatic Trail The distance by which a tire's cornering force acts behind the center of its contact patch, creating self-aligning torque.
  • Primary and Secondary Ride The two parts of ride quality, slow body motions controlled by springs and dampers and quicker harshness and shake.
  • Rack-and-Pinion Steering The steering mechanism in almost every modern car, in which a pinion on the steering shaft moves a toothed rack side to side.
  • Rear-Wheel Steering A system that turns the rear wheels a few degrees to tighten turning at low speed and improve stability at high speed.
  • Redundant Braking Unit RBU A backup brake module that lets an automated car still brake and stay stable if the main brake system fails.
  • Ride and Handling The two halves of how a car feels to drive, comfort over bumps and response and stability in maneuvers.
  • Ride Frequency The natural rate at which the body bounces on its springs, typically about 1 to 1.5 hertz on comfort-oriented cars.
  • Ride Height How high the body sits above the ground or wheel centers at a specified load.
  • Road Load Data Acquisition RLDA Driving an instrumented vehicle on tracks and roads to record the forces it experiences and set durability targets.
  • Roll Center An imaginary point, set by suspension geometry, about which the body leans in a corner.
  • Roll Stiffness Distribution The share of a car's resistance to body roll provided by the front suspension versus the rear, a key handling balance tool.
  • Rolling Resistance The energy a tire loses as it flexes while rolling, acting like a small constant brake on the car.
  • Run-Flat Tire A tire that can keep carrying the car for a limited distance after a puncture thanks to stiff sidewalls or an inner support.
  • Scrub Radius The distance at the road between the tire contact patch center and the point where the steering axis meets the ground.
  • Self-Aligning Torque SAT The twisting force a cornering tire produces that tries to steer the wheel back toward straight ahead.
  • Sideslip Angle The angle between the direction the car body points and the direction it actually travels.
  • Slip Angle The small difference between the direction a tire points and the direction it actually moves.
  • Solid Axle A single rigid beam linking the left and right wheels, so one wheel's movement affects the other.
  • Spring Rate How stiff a spring is, meaning the force needed to compress it a given distance, such as newtons per millimeter.
  • Sprung and Unsprung Mass The split between mass carried by the springs, mainly the body, and mass below them, such as wheels, brakes and hubs.
  • Static Stability Factor SSF A simple rollover risk number equal to half the track width divided by center of gravity height.
  • Steady-State Circular Test A standard handling test in which a car drives a fixed-radius circle at increasing speed to measure understeer.
  • Steer-by-Wire SbW Steering with no mechanical shaft between the steering wheel and road wheels, using sensors, motors and simulated feel.
  • Steering Angle Sensor SAS A sensor that measures how far and how fast the steering wheel is turned, a key input to stability control.
  • Steering Axis Inclination SAI The inward tilt of the steering pivot axis seen from the front, which helps self-centering and reduces scrub radius.
  • Steering Feel What the driver senses through the steering wheel, including effort buildup, on-center precision and road feedback.
  • Steering Knuckle The strong metal part at each front corner that holds the wheel hub and connects to suspension arms and steering linkage.
  • Steering Ratio How much the steering wheel must turn for the front wheels to turn one degree, typically around 12 to 18 to 1.
  • Steering System Everything that turns a vehicle's wheels when the driver turns the steering wheel, from the column to the tie rods.
  • Stopping Distance How far a vehicle travels from the moment braking starts until it comes to a stop.
  • Subframe A separate frame bolted under the body that carries the suspension, steering rack and often the engine or motor.
  • Suspension The springs, shock absorbers, links and bushings that connect the wheels to the body and control ride and handling.
  • Tie Rod The link between the steering rack and each front wheel's steering arm that pushes or pulls the wheel to steer it.
  • Tire: The rubber, fabric and steel assembly that is a vehicle's only contact with the road, shaping grip, braking, noise and range.
    Tire The rubber, fabric and steel assembly that is a vehicle's only contact with the road, shaping grip, braking, noise and range.
  • Tire Pressure Monitoring System TPMS A system that warns the driver when one or more tires are underinflated, using direct sensors or wheel speed data.
  • Tire Size Designation The sidewall code, such as 225/45R17 94W, that describes a tire's width, profile, construction, rim size, load and speed rating.
  • Toe The angle of the wheels relative to the car's center line seen from above, pointing slightly in or out.
  • Torque Steer A tug on the steering wheel under hard acceleration in a powerful front-wheel-drive car.
  • Torque Vectoring Sending different drive torque to individual wheels to help the car turn more sharply and stably.
  • Torsion Beam A simple rear suspension joining two trailing arms with a cross beam that twists, common on small front-drive cars.
  • Traction Control System TCS A system that stops the wheels spinning when accelerating on slippery surfaces by cutting power or braking the wheel.
  • Trailing Arm A suspension link running backward from a body pivot to the wheel, locating it fore and aft while letting it move up and down.
  • Turning Circle The diameter of the smallest circle a vehicle can drive around, measured at the outer wheels or outer body.
  • Understeer When the front tires lose grip before the rear ones and the car turns less than asked and runs wide.
  • Understeer Gradient A number in degrees per g that describes a car's basic cornering balance, measured in steady-state circle tests.
  • Vehicle Axis System The agreed axes engineers use to describe vehicle motion, with x forward, y sideways, z vertical and roll, pitch and yaw.
  • Vehicle Dynamics The engineering field that studies how a vehicle moves in response to the driver and to road and air forces.
  • Weight Distribution The share of a vehicle's weight carried by the front and rear axles, often quoted as a ratio such as 50/50.
  • Wheel Alignment Adjusting the wheel angles, mainly camber, toe and caster, to the manufacturer's specifications.
  • Wheel Bearing The bearing that lets each wheel spin smoothly on its axle or knuckle, usually as an integrated hub unit.
  • Wheel Speed Sensor WSS A sensor at each wheel that measures its rotational speed for ABS, traction control and stability control.
  • Yaw A vehicle's rotation about its vertical axis, the turning motion seen from above when a car corners or spins.

Full entry for members

Every term has a full entry for members: the plain-words definition, the practitioner note and the typed links between terms.

See membership

ACW Automotive Glossary, edition 2026.11.1. The headword and one line are open to everyone.