AutomotiveCloudWatch

Glossary · Manufacturing

Maintenance and Reliability

84 terms in the Manufacturing glossary, each with its one-line definition.

84 terms, A to Z

  • Airborne Ultrasound Monitoring Using a detector to hear high-frequency sound from air leaks, arcing and early bearing wear before they cause breakdowns.
  • Asset Criticality Ranking of machines by how serious their failure would be for safety, quality, output and cost, used to prioritize maintenance.
  • Asset Hierarchy Tree structure in maintenance software that files equipment from site down to repairable parts so costs and failures roll up correctly.
  • Asset Performance Management APM Software and practice that turn equipment sensor data and reliability analysis into decisions that prevent failures.
  • Autonomous Maintenance Practice where operators do basic care of their own machines, such as cleaning, inspecting, oiling and tightening.
  • B10 Life Running time or cycles by which 10 percent of a group of identical parts are expected to have failed.
  • Bad Actor Machine or component causing far more than its share of breakdowns, downtime or maintenance cost.
  • Bathtub Curve Graph of failure rate over a product's life with high early failures, a low steady middle and rising wear-out failures.
  • Burn-In Running new products under heat, voltage or load before shipment so weak units fail in the factory, common in electronics.
  • Clean, Inspect, Lubricate and Tighten CILT Four basic care tasks operators do on their own equipment from a short checklist, usually each shift.
  • Condition Monitoring Regularly measuring machine health signs such as vibration, temperature and oil condition to spot developing problems.
  • Condition-Based Maintenance CBM Doing maintenance when measured condition crosses a set limit, instead of on a fixed calendar.
  • Corrective Maintenance Maintenance done to fix equipment after a fault is found, either right away or planned for a later stop.
  • Critical Spares Spare parts stocked however rarely used because waiting for one during a breakdown would be very long or costly.
  • Deferred Maintenance Needed maintenance put off to a later window or because of budget limits, raising breakdown risk as it accumulates.
  • Early Equipment Management EEM TPM pillar that feeds lessons from existing machines into new equipment design so it reaches stable output quickly.
  • Eight Pillars of TPM Framework organizing Total Productive Maintenance into eight activity areas built on a 5S foundation.
  • Enterprise Asset Management EAM Software and practice for managing physical equipment across its whole life and many sites, broader than plant CMMS.
  • Failure Code Standard code recorded when a maintenance job closes, describing what failed, how, why and what was done.
  • Failure Mode Way in which an item fails, such as a bearing seizing or a seal leaking, the basis for FMEA and reliability analysis.
  • Failure Mode, Effects and Criticality Analysis FMECA Method that lists how an item can fail, the effects of each failure and ranks them by severity and likelihood.
  • Failure Rate How often an item fails per unit of time, such as failures per million hours, usually written as lambda.
  • Failure Reporting, Analysis and Corrective Action System FRACAS Closed-loop process that records every failure, finds its root cause and tracks the fix until proven effective.
  • Failure-Finding Task Scheduled check that a standby or protective device such as a relief valve or alarm still works when needed.
  • Focused Improvement TPM pillar in which cross-functional teams attack specific equipment losses using structured problem solving.
  • Fuguai Tag Tag hung on a machine to mark an abnormality found during operator care, tracked until the problem is fixed.
  • Improvement Maintenance Modifying equipment to remove the cause of repeated failures or ease maintenance, rather than simply repairing it.
  • Infrared Thermography Using an infrared camera to see heat and find hot spots in electrical connections, motors and bearings without contact.
  • ISO 14224 International standard for collecting and exchanging equipment reliability and maintenance data with common failure codes.
  • ISO 20816 Family of international standards for measuring machine vibration and judging whether it is acceptable.
  • ISO 55000 International family of standards for asset management, linking equipment decisions across their life to company goals.
  • Japan Institute of Plant Maintenance JIPM Japanese organization that developed and promotes Total Productive Maintenance and runs the TPM awards.
  • Job Plan Written instructions for a maintenance job listing steps, trades, time, parts, tools, permits and safety precautions.
  • Life Cycle Cost LCC Total cost of an asset over its life, from purchase and installation through operation, maintenance and disposal.
  • Lockout/Tagout LOTO Safety procedure that isolates and locks a machine's energy sources so it cannot start while someone services it.
  • Lubrication Applying oil or grease between moving parts to reduce friction and wear, a core routine maintenance task.
  • Maintainability How easily and quickly equipment can be repaired and returned to service, largely set at design and measured by MTTR.
  • Maintenance Backlog Approved maintenance work not yet done, measured in labor hours or weeks of crew capacity.
  • Maintenance Planning and Scheduling Preparing maintenance jobs with scope, parts and time in advance, then fitting them into windows when equipment is free.
  • Maintenance Prevention MP Designing new equipment to need little maintenance and be easy to clean, inspect and repair, using past lessons.
  • Maintenance Schedule Compliance Percentage of weekly scheduled maintenance work completed as scheduled, showing control over break-in work.
  • Maintenance, Repair and Operations MRO Supplies and services that keep a plant running but do not go into the product, such as spare parts and lubricants.
  • Management of Change MOC Formal procedure to review and approve changes to equipment, processes or staffing before they are made.
  • Motor Current Signature Analysis MCSA Checking the health of a motor and its driven machine by analyzing patterns in the current the motor draws.
  • Oil Analysis Testing lubricant samples for condition, dirt, water and wear metals to reveal oil health and internal machine wear.
  • One-Point Lesson OPL Short one-page training sheet with photos that explains one method or lesson and is taught in minutes at the machine.
  • Operator Rounds Regular walks in which operators check and record gauges, temperatures, leaks and noises to catch problems early.
  • Opportunistic Maintenance Doing maintenance tasks while a machine is already stopped for another reason, saving separate downtime.
  • Overhaul Major job that disassembles, inspects, repairs and reassembles equipment to bring it back near new condition.
  • P-F Curve Chart of a machine's decline from the first detectable sign of a problem to actual failure, used to set inspection intervals.
  • Permit to Work PTW Formal written system that lets hazardous work start only after hazards are assessed and controls are in place.
  • Planned Maintenance Maintenance scheduled in advance with defined tasks, parts and labor, as opposed to rushed repairs after failure.
  • Planned Maintenance Percentage PMP Share of all maintenance hours spent on planned work rather than emergency repairs.
  • PM Analysis JIPM technique for chronic losses that studies the physical phenomenon and lists every condition that could cause it.
  • Precision Maintenance Installing and keeping machines to tight alignment, balance, torque and lubrication standards so they last longer.
  • Predictive Maintenance PdM Maintenance timed by forecasting failure from trends in data such as vibration, temperature or oil quality.
  • Prescriptive Maintenance Approach that recommends what to do about a predicted failure and when, weighing risk, cost and production impact.
  • Preventive Maintenance PM Maintenance at fixed intervals of time, cycles or usage, such as changing filters every 500 hours, to make failure less likely.
  • Preventive Maintenance Compliance Percentage of scheduled preventive maintenance tasks completed within their allowed time window.
  • Preventive Maintenance Optimization PMO Structured review of an existing PM program to remove low-value tasks, add missing ones and shift to condition-based work.
  • Proactive Maintenance Maintenance that removes root causes of failure such as contamination and misalignment instead of reacting to symptoms.
  • Prognostics and Health Management PHM Discipline that monitors equipment condition, diagnoses faults and predicts how long it can keep running safely.
  • Quality Maintenance TPM pillar that targets zero defects by defining and holding the machine conditions that produce good parts.
  • Reactive Maintenance Fixing equipment only after it breaks, without a deliberate plan, a sign of an immature maintenance program.
  • Reliability Probability that a machine or part does its job without failing for a stated time under stated conditions.
  • Reliability-Centered Maintenance RCM Method that picks maintenance for each asset from its functions, failure modes and the consequences of each failure.
  • Remaining Useful Life RUL Estimate of how much longer a machine or part can run before failure or a set end-of-life limit.
  • Replacement Asset Value RAV Estimated cost of replacing a plant's equipment with new equipment of the same capability at today's prices.
  • Root Cause Failure Analysis RCFA Structured investigation of a machine failure to find its physical, human and organizational causes.
  • Rotor Balancing Adjusting the weight distribution of a spinning part such as a fan or spindle so it spins evenly without shaking.
  • Run-to-Failure RTF Deliberate choice to let a low-consequence item run until it breaks and then repair or replace it.
  • Seven Steps of Autonomous Maintenance JIPM sequence that moves operators step by step from initial cleaning to fully managing their own equipment care.
  • Shaft Alignment Positioning connected rotating shafts so their centerlines run straight within tight limits, preventing vibration and wear.
  • Shutdown Planned stop of a plant or line for major maintenance, retooling or model changeover, often during holidays.
  • Sixteen Major Losses JIPM list extending the six big equipment losses to losses in human work, energy, materials and tooling.
  • Society for Maintenance and Reliability Professionals SMRP US-based nonprofit society known for standard maintenance metric definitions and the CMRP certification.
  • Spare Parts Replacement parts kept in stock to repair equipment, balancing faster repairs against tied-up money and space.
  • Total Productive Maintenance TPM Japanese maintenance approach in which everyone, especially operators, keeps equipment in top condition to reach zero losses.
  • TPM Award Awards from the Japan Institute of Plant Maintenance to sites that have implemented TPM to a high standard.
  • Vibration Analysis Checking rotating machines by measuring vibration, since faults such as imbalance or bearing wear leave distinct patterns.
  • Weibull Analysis Statistical method fitting a curve to failure data to show whether parts fail early, at random or from wear-out.
  • Work Order Record that authorizes and describes a maintenance job and, once closed, builds the machine's repair history.
  • Work Request Report from an operator or anyone of a problem or needed job, approved before it becomes a work order.
  • Wrench Time Share of a maintenance technician's shift spent on actual hands-on work rather than travel, waiting or permits.

Full entry for members

Every term has a full entry for members: the plain-words definition, the practitioner note and the typed links between terms.

See membership

ACW Manufacturing Glossary, edition 2026.11.1. The headword and one line are open to everyone.