Signals · Article · Automotiveシグナル · 記事 · 自動車
Drive-by-Wire [Explained]
Autonomy gets the headlines. The quieter change is that the steering wheel and brake pedal are becoming input devices, and the cars still have to stop when the electronics fail.

Most drivers assume the steering wheel is physically connected to the front wheels and the brake pedal pushes fluid to the brakes. In most cars on the road today, both assumptions are still true. I have heard engineers loosely call modern electric power steering steer-by-wire, and I have blurred the line myself. It is not the same thing, and the difference is where this story gets interesting.
Drive-by-wire means replacing mechanical and hydraulic links between the driver and the car with sensors, computers and electric actuators. The accelerator went first, decades ago. Brakes are partway there. Steering without any mechanical connection is now in production in a handful of vehicles. Each step makes new features possible, from smoother regenerative braking to yoke-shaped steering wheels to automated driving, and each one puts more of the car’s most basic safety functions in the hands of software. This article explains how the systems work, where they came from, and why getting them approved has taken more than twenty years.
Aircraft did it first
The idea came from aviation. NASA’s Lunar Landing Research Vehicle, which first flew on 30 October 1964, was controlled through analog computers rather than mechanical linkages, and NASA describes it as the first pure fly-by-wire aircraft to fly in Earth’s atmosphere. On 25 May 1972 NASA flew a modified F-8C fighter using a digital computer borrowed from the Apollo guidance system, with no mechanical backup to the flight controls. The program ran 211 flights and was later upgraded to triple-redundant computers.
Commercial aviation followed. Concorde used an analog fly-by-wire system, and the Airbus A320, which first flew on 22 February 1987 and entered service in spring 1988, became the first airliner with digital fly-by-wire and sidestick controls.
Cars inherited the central lesson. A fly-by-wire aircraft runs several independent computers in parallel, compares their outputs and votes out any channel that disagrees. Redundancy is not an add-on. It is the design. Cars borrowed the principle, usually as two self-checking channels that monitor each other rather than three voting computers.
The pedal you already drive by wire
Electronic throttle control is the oldest and most widespread form. BMW is generally credited with the first production system on the 7 Series in 1988, and Chevrolet used one on the 1997 C5 Corvette. The accelerator pedal carries two or three position sensors, often wired so their signals mirror each other, and a computer opens the throttle with an electric motor. If the sensors disagree, the car falls back to a limited limp-home mode. Today almost every new gasoline car works this way, and in an electric car there is no throttle cable to remove in the first place.
It also produced the first great public argument about software in car control. After reports of unintended acceleration in Toyota vehicles, NHTSA and NASA ran a ten-month study published in February 2011 that reviewed some 280,000 lines of code and found no electronic cause, while mechanical problems such as pedal entrapment had already been recalled. NASA did not claim to have proven the software was flawless, and that distinction mattered in later court cases. The episode showed that by-wire systems have to be explainable after something goes wrong, not just safe in normal operation.
Shift-by-wire, where the gear selector sends only an electrical signal, brought a different lesson. In 2016 Fiat Chrysler recalled about 811,000 US vehicles because drivers misunderstood a monostable shifter that springs back to the center position, and some cars rolled away after drivers believed they were in park. The electronics worked as designed. The interface did not. The fix added logic that puts the car in park automatically.
That distinction runs through every by-wire system. Removing a mechanical link removes the physical feedback that told the driver what the car was doing, so the system has to recreate that feedback deliberately, through pedal feel, steering resistance or clear warnings.
Brakes that think before they squeeze
Brake-by-wire comes in two families. In electro-hydraulic or wet systems, the pedal is disconnected from the brakes in normal operation. A pedal simulator gives the driver a natural feel, a computer reads how hard the pedal is pressed, and an electric pump creates the hydraulic pressure that squeezes conventional calipers. If the electronics fail, a hydraulic path from the pedal still works. In electromechanical or dry systems, motors at each wheel clamp the brake pads directly and there is no brake fluid at all.
Mercedes-Benz and Bosch put an early wet system, Sensotronic Brake Control, into the SL in October 2001 and the E-Class soon after. It was a sign of what was coming, and a warning. In May 2004 Mercedes recalled about 680,000 vehicles worldwide over the system, and in 2006 it dropped SBC from the E-Class and returned to conventional brakes, citing cost and customer confidence. The hydraulic fallback had kept the cars able to stop. The reputation damage was enough.
Hybrids and electric vehicles revived the idea for a practical reason. To recover as much energy as possible, the car needs to decide, from moment to moment, how much braking comes from the electric motor and how much from friction. A decoupled pedal lets software blend the two without the driver feeling the switch.
The modern generation packs everything into one compact unit. Continental’s MK C1, which entered series production in 2016 on the Alfa Romeo Giulia, combines the master cylinder, brake booster and stability control in one box and builds pressure in about 150 milliseconds, roughly twice as fast as a conventional system according to Continental. ZF’s Integrated Brake Control appeared on the 2019 Chevrolet Silverado and GMC Sierra, and ZF says its Fowlerville, Michigan plant has now built 10 million units.
One common confusion is worth clearing up. Bosch’s iBooster, in production since 2013, replaces the vacuum booster with an electric motor and can blend regenerative braking, but the pedal stays mechanically connected to the master cylinder. It is an electric booster, not full brake-by-wire.
The dry brake arrives
Fully electromechanical brakes have been promised for twenty years and are now reaching production. They remove brake fluid, which absorbs water and needs periodic replacement, let each wheel be controlled independently and can respond faster. They also make the car’s electrical supply part of the braking system, which is why regulators wanted new rules first.
Those rules arrived in 2025 and 2026. A new series of amendments to UN Regulation 13-H, which entered into force in June 2025, adds requirements for braking systems that depend only on electrical energy, including energy management, staged warnings and a low-energy emergency function. China’s revised braking standard GB 21670-2025 took effect for new type approvals on 1 January 2026 and gives electromechanical braking a legal basis there.
Production followed quickly. Several companies now claim firsts. Chery says its Exeed EX7, launched in China in April 2026, is the first mass-produced car with fully electromechanical brakes, a claim Li Auto disputes. Brembo announced in May 2026 that its fluid-free Sensify system had entered series production for an unnamed global manufacturer. ZF won an order in January 2025 for about 5 million vehicles that combines dry brakes on the rear axle with hydraulic brakes at the front, which may turn out to be the most common first step.
Steering without a shaft
Almost every new car already has electric power steering. A motor helps turn the rack, but a steel column and shaft still connect the wheel to the wheels. True steer-by-wire removes that connection. Sensors read the steering wheel angle and torque, controllers command motors on the steering rack, and a separate motor in the steering wheel recreates the road feel the driver would otherwise lose.
Infiniti brought the first production version to the 2014 Q50 with Direct Adaptive Steering. It used three controllers that monitored each other and kept a steering column linked through a clutch that stayed open in normal driving and closed if something failed. In November 2013 Infiniti recalled 23 US cars over a software problem that, at very low temperatures, could disable the electric steering and delay that backup clutch. A larger software recall of about 60,000 Q50s followed in 2016. Both showed how carefully regulators would treat this function.
Tesla’s Cybertruck, delivered from 30 November 2023, is generally credited as the first production vehicle with full steer-by-wire and no mechanical column. Tesla describes redundant motors, sensors, power supplies and communication paths, and the truck goes from lock to lock in about 340 degrees of wheel rotation, roughly one turn, with speed-dependent ratios and rear-wheel steering of about 10 degrees. Its steering runs on the truck’s 48-volt electrical system.
Other manufacturers followed with their own versions. China’s industry ministry approved steer-by-wire for the NIO ET9 in December 2024 using a ZF system, and deliveries began in March 2025. Lexus launched steer-by-wire on the RZ in Europe in 2025, pairing it with a yoke and about 200 degrees of travel in each direction. Mercedes-Benz announced its system in April 2025 and launched it on the updated EQS in 2026.
Mercedes’ description is a useful example of how much redundancy goes into one function. The company says its architecture duplicates sensors, controllers, power supply and onboard data paths, and uses twice the number of actuators strictly required. If everything in the steering path still failed, the car could use its rear-axle steering and wheel-by-wheel braking to keep control. Mercedes says the system completed more than a million kilometers of bench testing before launch.
Redundancy is the whole design
There are two broad strategies for failure. One falls back to something simpler, such as Infiniti’s mechanical clutch or the hydraulic push-through path in most wet brake systems, and accepts degraded operation. The other is fail-operational. It keeps providing the function after a single fault, often at reduced performance, using duplicated electronics with no mechanical backup at all. A steering system at highway speed has no passive safe state, so it has to keep working long enough to bring the car to one. Full steer-by-wire and dry brakes need fail-operational designs, because there is nothing mechanical left to fall back on.
That means doubling or tripling almost everything. Two or three sensors measure the same input so a disagreement can be detected. Independent controllers run in parallel and check each other. Separate power feeds and communication paths make sure one broken wire cannot take out both channels. Safety goals for steering and braking, such as preventing loss of steering or unintended braking, are typically rated ASIL D, the most demanding level in ISO 26262.
The electrical supply itself becomes a safety system. Both the new UN brake rules and China’s new steering standard require energy management and warnings when the supply weakens, because a by-wire car with a failing battery is a car that may not be able to stop or steer. This is also where 48-volt systems help. For a steering motor drawing several kilowatts, 48 volts needs a quarter of the current that 12 volts would, which allows thinner wires and less heat. It helps, but steer-by-wire does not strictly depend on it.
Feel is the last piece, and it is not cosmetic. A driver judges grip and speed partly through the steering wheel and pedal. By-wire systems have to decide which signals from the road to pass through and which to filter out, and get that judgment right across every surface and speed.
Why regulators took two decades
Europe never banned steer-by-wire outright, which surprises many people. UN Regulation 79 has allowed fully powered steering without a mechanical link since 2003. But its rules for what happens after a fault, including a limit on continuing to drive above 10 km/h once a failure warning appears, made a design with no mechanical backup impractical unless it could keep working normally after a fault. The German industry association VDA, together with international manufacturer and supplier bodies, has been drafting changes to R79 since 2024 to widen what is permitted.
China moved faster. After approving the NIO ET9 case by case in December 2024, it published GB 17675-2025, which took effect on 1 July 2026 and removes the mandatory mechanical link between the steering wheel and the road wheels for systems that demonstrate redundancy, warnings, degradation strategies and ISO 26262 functional safety.
Adoption will still be gradual. ZF has told Automotive Testing Technology International it expects steer-by-wire to reach 2 to 5 percent of new vehicles by 2030. The technology works. What slows it down is cost, certification and convincing buyers that a steering wheel with no shaft behind it is safe.
What by-wire really means
Drive-by-wire turns the driver’s controls into requests. The steering wheel and pedals stop being the mechanism and become input devices to a set of computers that decide what the car should do. That is what lets a software-defined vehicle change how it brakes or steers after it is sold, and what lets an automated driving system command the car without a human hand on the wheel.
It also moves the hardest safety question in the car into software and electronics. For any program, the real test sits in the second after something fails. What does the car do next, and how much evidence can the manufacturer show that it will still stop and steer?
Words you will hear
Drive-by-wire. Replacing mechanical or hydraulic links between driver controls and the vehicle with sensors, controllers and electric actuators.
EPS. Electric power steering. A motor assists steering, but a mechanical column still connects the wheel to the steering rack.
Steer-by-wire. Steering with no mechanical connection between the steering wheel and the road wheels in normal operation.
Wet brake-by-wire. An electro-hydraulic system where the pedal is decoupled and an electric pump creates hydraulic brake pressure.
EMB or dry brake-by-wire. Electromechanical brakes where motors at each wheel clamp the pads directly, with no brake fluid.
Fail-operational. A design that continues to provide the function, possibly at reduced performance, after a single fault.
Feedback actuator. The motor in a steer-by-wire steering wheel that recreates road feel for the driver.
This article is part of the AutomotiveCloudWatch Explained series, which also covers software-defined vehicles, zonal architecture, in-vehicle networks, over-the-air updates and autonomous driving. For the safety-certified operating system that often runs underneath these controllers, read How QNX Works and Why It Is Difficult to Replicate.
How QNX Works and Why It Is Difficult to Replicate
If this helped, subscribe free at automotivecloudwatch.com to get each new explainer when it publishes.
All opinions are my own and do not reflect those of my employer.
Get the next Executive Briefing by email
Each new briefing, in your inbox.
Subscribe



